12/16/2023 0 Comments Dremel port and polish kit![]() Front and rear lowering kit for ice racing, Herrmann racing +1" steering stem, Pro Taper Contour Bars, ODI lock on Grips.įriends dont let Friends drive stock quads!!Īfter several afternoons and nights, using a dremel and sanding rolls, there's a noticed increase in power when done right. *Port and Polish Cylinder Head, 3- Angle Valve JobĬylinder Works jug, Hot rods +5mm stroker crank, CP stroker piston, Stage 3 / Old School hot cams, DRZ valve springs, +1mm Ferrea valves, Port and polished head, D.I.D 3/4 pitch camchain, K&N Air filter with 400ex air boot, Sudco/Sparks FCR 41 mm carb, R&D accelerator pump with adjustable leak jet 1.5 turns out, 50 pilot 185 main jet, needle on 3rd clip 2.0 turns out with edelbrock headstay mount, LRD custom aluminum air box, FMF Factory 4 exhaust, Dyna FS CDI, Dirt digger clutch, Janssen outlaw ball joints, GT Thunder Shocks, GT Thunder Linkage, Janssen MX-Tech +2 A-arms, Maxxis razr cross Front and ITP SX rear tires, ITP T9 Front Rims Douglas single beadlock rear rims, H-bomb Decal Kit, Maier race plastics Pro Armor Mx bumper and Skids, Moose Racing nerfs, Streamline Front and Rear Brake lines, Bare Performance Gusset Kit, powermadd hanguards, maximizer foot pegs, UM rad shrouds, moose racing brake block off plate, JB racing swing arm, twin row honda style axle carrier, honda 400ex hubs and rear brake caliper, RPM +4" axle, lonestar antifade honda brake hub. ~DRZe Kit (DID Chain, Seals, Gaskets, Valve Springs, 12.2 Compression) Waiting mods to install: The closet is getting full =-) ![]() Special Tools along the way: 5mmx.50 Tap, Custom Machined Flywheel Puller, Tusk V-Spring Compressor. ![]() I am a fan of: Liquid Performance Cycle Wash, SC1 Silicone Detailer Spray, Silkolene (NO SLING) Chain Lube, and Maxima Kool-Aid =-) ![]() 2005 Suzuki LTZ400 (Yellow and Black): AC Racing Nerf Bars, Full Aluminum Skid Plates, PRM Aluminum Grab Bar, Moose Pro Plate Front Bumper, Lonestar E-Brake Block-off, FMF Corporate Graphics Kit, Pro-Design Case Saver, ESR Airbox Eliminator Intake, ESR Case Breather Filter, ESR Pre-Filter, Zip~n~Z Splashgaurd, FMF Titanium 4 Exhaust 14", FMF Powerbomb Head-Pipe Stainless Steel (w/ Mid-Pipe), 2" OD Exhaust Tip, 39mm FCR Carb Swap (Idle Screw Mod, TPS-Tors Removal Mod, Pro-Motion T-Cable, Ride Engineering Fuel Screw, Yamaha Raptor Petcock, Custom Head-Boot) NCVQ Needle 3rd Clip, 168MJ, 45 Pilot Jet, 40 Leak Jet, 2.25 Turns Out on Fuel Screw (Elevation 1,023ft), Trail Tech -16oz Flywheel, DynaTek Non-Programmable Ignition, CRT Performance Thermo Sensor, FX Radiator Temperature Gauge, Maxima Kool-Aid, 3.50" In-line Super Cooler ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |